Mat.No. 1.2235/DIN 80CrV2/AISI L2
Designation by Standards
| Mat. No. | DIN | EN | AISI |
| 1.2235 | 80CrV2 | - | L2 |
Chemical Composition (in weight %)
| C | Si | Mn | Cr | Mo | Ni | V | W | Others |
| 0.80 | 0.33 | 0.40 | 0.55 | - | - | 0.20 | - | - |
Applications
Circular saws for timber, saws for non ferous, machine saws, measuring tools, tools for wood working (axes, knivesp, punches, guide rods, twist drills, reamers, ejector pins, dentist’s drills.
Physical properties (average values) at ambient temperature
Modulus of elasticity [103 x N/mm2]: 210
Density [g/cm3]: 7.80
Thermal conductivity [W/m.K]: 33.5
Soft Annealing
Heat to 710-850oC, cool slowly in furnace. This will produce a maximum Brinell hardness of 220.
Stress Relieving
Stress relieving to remove machining stresses should be carried out by heating to approx. 650oC, holding for 1-2 hours at heat, followed by air cooling. This operation is performed to reduce distortion during heat treatment.
Hardening
Harden from a temperature of 810-840oC, 780-810oC followed by oil (up to diamter 15 mm) or water (for diameter higher then 15 mm) quenching Hardness after quenching is 64 HRC.
Tempering Temperature (oC) vs. Hardness (HRC)
| 100oC | 200oC | 300oC | 400oC | 500oC | 550oC | 600oC |
| 64 | 62 | 57 | 51 | 44 | 40 | 31 |
Forging
Hot forming temperature: 1050-850oC.
Machinability
No data.Corrosion Resistance
This is an alloy steel and it is not corrosion resistant. It will rust unless protected.
Disclaimer
The information and data presented herein are typical or average values and are not a guarantee of maximum or minimum values. Applications specifically suggested for material described herein are made solely for the purpose of illustration to enable the reader to make his own evaluation and are not intended as warranties, either express or implied, of fitness for these or other purposes. There is no representation that the recipient of this literature will receive updated editions as it become available.
Designation by Standards
| Mat. No. | DIN | EN | AISI |
| 1.2235 | 80CrV2 | - | L2 |
Chemical Composition (in weight %)
| C | Si | Mn | Cr | Mo | Ni | V | W | Others |
| 0.80 | 0.33 | 0.40 | 0.55 | - | - | 0.20 | - | - |
Applications
Circular saws for timber, saws for non ferous, machine saws, measuring tools, tools for wood working (axes, knivesp, punches, guide rods, twist drills, reamers, ejector pins, dentist’s drills.
Physical properties (average values) at ambient temperature
Modulus of elasticity [103 x N/mm2]: 210
Density [g/cm3]: 7.80
Thermal conductivity [W/m.K]: 33.5
Soft Annealing
Heat to 710-850oC, cool slowly in furnace. This will produce a maximum Brinell hardness of 220.
Stress Relieving
Stress relieving to remove machining stresses should be carried out by heating to approx. 650oC, holding for 1-2 hours at heat, followed by air cooling. This operation is performed to reduce distortion during heat treatment.
Hardening
Harden from a temperature of 810-840oC, 780-810oC followed by oil (up to diamter 15 mm) or water (for diameter higher then 15 mm) quenching Hardness after quenching is 64 HRC.
Tempering Temperature (oC) vs. Hardness (HRC)
| 100oC | 200oC | 300oC | 400oC | 500oC | 550oC | 600oC |
| 64 | 62 | 57 | 51 | 44 | 40 | 31 |
Forging
Hot forming temperature: 1050-850oC.
Machinability
No data.Corrosion Resistance
This is an alloy steel and it is not corrosion resistant. It will rust unless protected.
Disclaimer
The information and data presented herein are typical or average values and are not a guarantee of maximum or minimum values. Applications specifically suggested for material described herein are made solely for the purpose of illustration to enable the reader to make his own evaluation and are not intended as warranties, either express or implied, of fitness for these or other purposes. There is no representation that the recipient of this literature will receive updated editions as it become available.
