Availability: | |
---|---|
PDF Export | |
Mat.No. 1.3520/DIN 100CrMn6
Designation by Standards
Mat. No. | DIN | EN | AISI |
1.3520 | 100CrMn6 | - | - |
Chemical Composition (in weight %)
C | Si | Mn | Cr | Mo | Ni | V | W | Others |
0.97 | 0.60 | 1.10 | 1.53 | - | - | - | - | - |
Applications
Roller bearings with thickness up to 50mm.
Physical properties (average values) at ambient temperature
Modulus of elasticity [103 x N/mm2]: 210
Density [g/cm3]: 7.85
Soft Annealing
Heat to 760-800oC, cool slowly in furnace. This will produce a maximum Brinell hardness of 217.
Normalizing
Normalizing temperature: 860-900oC.
Stress Relieving
Stress relieving to remove machining stresses should be carried out by heating to approx. 650oC, holding for 1-2 hours at heat, followed by air cooling. This operation is performed to reduce distortion during heat treatment.
Hardening
Harden from a temperature of 830-890oC followed by oil quenching. Hardness after quenching is approx. 64 HRC.
Tempering Temperature (oC) vs. Hardness (HRC)
100oC | 200oC | 300oC | 400oC |
63.5 | 60.5 | 55 | 51 |
Forging
Hot forming temperature: 1100-850oC.
Disclaimer
The information and data presented herein are typical or average values and are not a guarantee of maximum or minimum values.Applications specifically suggested for material described herein are made solely for the purpose of illustration to enable the reader to make his own evaluation and are not intended as warranties, either express or implied, of fitness for these or other purposes.
There is no representation that the recipient of this literature will receive updated editions as it becomes available.
Designation by Standards
Mat. No. | DIN | EN | AISI |
1.3520 | 100CrMn6 | - | - |
Chemical Composition (in weight %)
C | Si | Mn | Cr | Mo | Ni | V | W | Others |
0.97 | 0.60 | 1.10 | 1.53 | - | - | - | - | - |
Applications
Roller bearings with thickness up to 50mm.
Physical properties (average values) at ambient temperature
Modulus of elasticity [103 x N/mm2]: 210
Density [g/cm3]: 7.85
Soft Annealing
Heat to 760-800oC, cool slowly in furnace. This will produce a maximum Brinell hardness of 217.
Normalizing
Normalizing temperature: 860-900oC.
Stress Relieving
Stress relieving to remove machining stresses should be carried out by heating to approx. 650oC, holding for 1-2 hours at heat, followed by air cooling. This operation is performed to reduce distortion during heat treatment.
Hardening
Harden from a temperature of 830-890oC followed by oil quenching. Hardness after quenching is approx. 64 HRC.
Tempering Temperature (oC) vs. Hardness (HRC)
100oC | 200oC | 300oC | 400oC |
63.5 | 60.5 | 55 | 51 |
Forging
Hot forming temperature: 1100-850oC.
Disclaimer
The information and data presented herein are typical or average values and are not a guarantee of maximum or minimum values.Applications specifically suggested for material described herein are made solely for the purpose of illustration to enable the reader to make his own evaluation and are not intended as warranties, either express or implied, of fitness for these or other purposes.
There is no representation that the recipient of this literature will receive updated editions as it becomes available.